TFT LCD monitors are
rapidly becoming shipped with new computers by default. On this page I
explain you the frequent trouble of TFT monitor and how to resolve them.
No display or white screen:
If this is a new install make sure the refresh rate is not set too high. If you installed a new video card in your system make sure the refresh rate is not set too high. Under Windows, reboot the system and go into “Safe Mode” (Use F8 key on boot up) select safe mode and change the refresh rate under display properties to either 60Hz or Default. Then reboot the system and the screen will turn on. Maximum mode on 15″ TFT screens is 1024×768 and maximum mode on 17″ and 19″ TFT is 1280×1024. Check to see if the green light is on with the external power adapter. Make sure all plugs are secure and the video cable is properly attached to the computer.
Dark screen in games:
TFT Liquid Crystal Display monitors are a unique devices that are manufactured to meet excellent picture clarity and reproduction in a native mode. Outside a native mode graphics will be darker, fine lines and text will be thicker. Native mode for 15″ TFT panels is 1024×768, 17″ and 19″ TFT panels are 1280×1024. Most games can be configured to run at 1024×768 which should produce clean graphics.
Thick text:
As described above, TFT LCD monitors perform best in their native modes. Other modes can be used however the reproduction of text will vary in thickness depending on the mode the monitor is running in. Best text reproduction is view in the monitors native mode.
Faint or unseen text:
TFT monitors are Bright! So bright that sometimes text in a DOS program may be very faint or not seen. In order to see this text, you can reduce the contrast level down until the text is visible. TFT LCD monitors were manufactured to perform in a GUI environment such as Windows, Linux (X) and Macintosh. Older designed programs may have upgrades to enhance this effect to make the text legible.
Wavy lines on the screen:
In some instances you may encounter wavy lines on the screen. These are usually 1/4″ thick and move in a vertical motion. This is caused by a noisy electrical feed from a wall outlet. If you change your vertical refresh rate under display properties to 75Hz this effect should disappear.
Small dot on screen:
TFT panels by their very nature are difficult to manufacture. KDS uses displays from various suppliers including; Samsung, Hyundai and Acer, who all guarantee the display to be 99.99% free from pixel defect. What that means is a 15″ LCD display can have up to about 6-10 broken pixels and still be considered “acceptable”. Broken pixels are individual pixels, which are stuck on, off, or as one particular color. Depending on their location and intensity, they can be next to invisible or obvious. This is common to ALL TFT screens and is not considered a defect by the screen manufacturer.
Dark areas:
Retail TFT LCD monitor products employ the use of a single TFT backlight. This backlight is responsible to deliver full edge to edge brightness across the screen. On some models the screen may not be as bright in the center or the edges as other areas. This is due to the design the actual panel manufacture took to keep costs down so that the TFT panel is affordable for the retail environment. Prices of TFT panels vary according to added features (TV tuner, SVIDEO etc.). They also vary according to the number of backlights that are in the panel. High-bright monitors with multiple backlights can cost upwards of $2,500.00 for a 15″ panel.
If this is a new install make sure the refresh rate is not set too high. If you installed a new video card in your system make sure the refresh rate is not set too high. Under Windows, reboot the system and go into “Safe Mode” (Use F8 key on boot up) select safe mode and change the refresh rate under display properties to either 60Hz or Default. Then reboot the system and the screen will turn on. Maximum mode on 15″ TFT screens is 1024×768 and maximum mode on 17″ and 19″ TFT is 1280×1024. Check to see if the green light is on with the external power adapter. Make sure all plugs are secure and the video cable is properly attached to the computer.
Dark screen in games:
TFT Liquid Crystal Display monitors are a unique devices that are manufactured to meet excellent picture clarity and reproduction in a native mode. Outside a native mode graphics will be darker, fine lines and text will be thicker. Native mode for 15″ TFT panels is 1024×768, 17″ and 19″ TFT panels are 1280×1024. Most games can be configured to run at 1024×768 which should produce clean graphics.
Thick text:
As described above, TFT LCD monitors perform best in their native modes. Other modes can be used however the reproduction of text will vary in thickness depending on the mode the monitor is running in. Best text reproduction is view in the monitors native mode.
Faint or unseen text:
TFT monitors are Bright! So bright that sometimes text in a DOS program may be very faint or not seen. In order to see this text, you can reduce the contrast level down until the text is visible. TFT LCD monitors were manufactured to perform in a GUI environment such as Windows, Linux (X) and Macintosh. Older designed programs may have upgrades to enhance this effect to make the text legible.
Wavy lines on the screen:
In some instances you may encounter wavy lines on the screen. These are usually 1/4″ thick and move in a vertical motion. This is caused by a noisy electrical feed from a wall outlet. If you change your vertical refresh rate under display properties to 75Hz this effect should disappear.
Small dot on screen:
TFT panels by their very nature are difficult to manufacture. KDS uses displays from various suppliers including; Samsung, Hyundai and Acer, who all guarantee the display to be 99.99% free from pixel defect. What that means is a 15″ LCD display can have up to about 6-10 broken pixels and still be considered “acceptable”. Broken pixels are individual pixels, which are stuck on, off, or as one particular color. Depending on their location and intensity, they can be next to invisible or obvious. This is common to ALL TFT screens and is not considered a defect by the screen manufacturer.
Dark areas:
Retail TFT LCD monitor products employ the use of a single TFT backlight. This backlight is responsible to deliver full edge to edge brightness across the screen. On some models the screen may not be as bright in the center or the edges as other areas. This is due to the design the actual panel manufacture took to keep costs down so that the TFT panel is affordable for the retail environment. Prices of TFT panels vary according to added features (TV tuner, SVIDEO etc.). They also vary according to the number of backlights that are in the panel. High-bright monitors with multiple backlights can cost upwards of $2,500.00 for a 15″ panel.
